Universal backup OpenATV 7.0 firmware for any MIPS/ARM receiver with Oscam iCam v9

1. introduction

We have a universal backup for you (with Oscam iCam v9 ) prepared for any Enigma2 receiver with OpenATV 7.0 firmware with MIPS or ARM CPU.

Attention! After using our backup, all data on your receiver will be deleted! Including your scanned channels etc. Therefore, we strongly recommend making a full backup of your receiver before installing!

After you have used our backup, you need to make some settings - if necessary, change the configuration of your tuner and enter your data for connecting to the CS server.

2. Restore from a universal backup for any Enigma2 receiver with OpenATV 7.0 firmware (MIPS and ARM)

  1. In order to use our backup, you must OpenATV 7.0 Install firmware on your receiver. We used OpenATV 7.0 firmware dated September 2, 2022. Download and install OpenATV 7.0 from the official website – https://www.opena.tv/downloads/ . If you already have a previous version of OpenATV, upgrade to version 7.0 by Menu -> Setup -> Software Management -> Use Flash Online
  2. Format your USB stick with a FAT32 file system
  3. Insert the USB stick into your receiver
  4. Make a backup copy of your receiver's settings on a USB stick. To do this, use the function Menu -> Setup -> Software Management -> Backup System Settings . You should see a message on the screen – Backup Complete .
  5. Remove the USB stick from the receiver and insert it into your PC
  6. Download a ready-made backup from our website:
    • ARM processor ( blank root password for ssh/telnet and web interface)
    • ARM processor (Root password for ssh/telnet and web interface is icam2022 )
    • MIPS processor ( empty root password for ssh/telnet and web interface)
    • MIPS processor (Root password for ssh/telnet and web interface is icam2022 )
  7. Go to the USB stick. You see the folder backup_openatv_BOXMANE (e.g. backup_openatv_vuuno4k for VU+ UNO 4k). Go to this folder and replace the file enigma2settingsbackup.tar.gz through the file you downloaded from our website (delete the file from the flash drive and insert the file enigma2settingsbackup.tar.gz that you downloaded from our website into this folder).
  8. Insert the USB stick into your receiver
  9. Go to Menu -> Setup -> Software Management -> Restore System Settings. The recipient asks you, “Are you sure you want to restore the backup?” Answer – YES
  10. ATTENTION! After the backup is restored, the recipient asks: “Backup plugins found. Do you want to install?". Answer - NO . It is important!!!
  11. Receiver will automatically restart. Now can Remove the USB stick from the receiver.
  12. Go to step 3

3. Setting up the receiver after flashing

3.1 Tuner configuration

If after flashing and turning on the receiver the channel “ cable one “ didn’t work for you, you need to change the tuner settings. To do this, go to the area MENU -> Setup -> Reception -> Tuner configuration and configure your tuner.

3.2 Obtaining the recipient's IP address

By default, the recipient should automatically obtain a network address (DHCP). To find out, you need to go to the section Go to MENU -> Information -> Network

Connection status must Up/Active be , IP address needs to be defined (In my case it is 192.168.1.219)

If for some reason your receiver did not automatically receive an address, you will need to set up the network manually. This can be done in section MENU -> Setup -> System -> Network -> Device settings -> Adapter settings

3.3 Set up Oscam

You need to add your access parameters to Oscam. To do this, open this Oscam web interface in a browser with the IP of your receiver. The Oscam web interface is on Port 8080 . In my case it is:

 http://192.168.1.219:8080/

You have to go to the section Files -> oscam.server go to , enter your connection details from the billing and click the button Save click.

Don't forget to click on that Save button to click!

4. Restart the receiver

Please restart the receiver completely after setup. Do not switch the receiver off via the socket, but restart it via the menu MENU -> Standby / Restart -> Reboot

5. Choose a playlist and watch it!

After restarting the receiver you can go to Sky Germany iCAM Bouquet go and enjoy the view.

6. Additional Information

Installed firmware has a root password for remote access via SSH/Telnet :

 Login: root 
Password: icam2022

We recommend that you change the root password and restrict or disable remote access when you don't need it.

7. Changing the ROOT password

To increase the security of your receiver, we strongly recommend that you change the root password.
To change the root password, log in to the receiver via SSH or Telnet using the login and password specified in Section 6. Enter the command:

 Password root

and set your new password