Universal backup VTi 15.0.01 firmware for all VU+ (MIPS/ARM) receivers with Oscam iCam v9

1. introduction

We have a universal backup for you (with Oscam iCam v9 ) for each VU Plus - Receiver with VTi 15.0.01- Firmware prepared with MIPS or ARM CPU.

Attention! After using our backup, all data on your receiver will be deleted! Including your scanned channels etc. Therefore, we strongly recommend that you make a full backup of your receiver before installing!

After you have used our backup, you need to make some settings - if necessary, change the configuration of your tuner and enter your data for connecting to the CS server.

2. Restore from a universal backup for any VU+ receiver with VTi firmware (MIPS and ARM)

2.1 Firmware installation on your Vu+

First of all you have to ORIGINAL VTi 15.0.01 Install on your VU Plus receiver (if not already installed)!

  1. Format your USB stick with a FAT32 file system
  2. Load the USB image down HERE
  3. Extract the USB image (it's a .zip archive) on your PC to the root directory of your USB stick using your favorite unzip tool. The result is that you will get a directory vuplus and in this directory you will find a directory zero4k where you will find the necessary files.
  4. Turn off the receiver.
  5. Make sure no other USB devices are connected to the receiver while flashing
  6. Insert the USB stick containing the image files into one of the USB ports on the receiver, if possible the rear USB port is recommended.
  7. Turn on the receiver.
  8. The WHITE VU+ logo will flash quickly two or three times and then begin to fade in and out slowly.
  9. Once the process is complete, the WHITE VU+ logo will flash quickly.
  10. Switch off the receiver, remove the USB stick and switch the receiver back on.
  11. Now you can start configuring the Zero 4K. See instructions below (Go to Step 3)

2.2 Restore from backup

  • Format your USB stick with a FAT32 file system
  • Insert the USB stick into your receiver
  • Go to section MENU -> VTi -> Device Manager .
  • Select your USB drive and press the OK button.
  • Your flash drive will be prepared for the VU receiver. Please leave Section Device Manager
  • Remove your USB stick from the receiver and insert it into your PC
  • Download a ready-made backup from our website:
    • ARM processor ( empty root password for ssh/telnet and web interface)
    • ARM processor (Root password for ssh/telnet and web interface is icam2022 )
    • MIPS processor ( empty root password for ssh/telnet and web interface)
    • MIPS processor (Root password for ssh/telnet and web interface is icam2022 )
  • Unpack the downloaded archive onto your flash disk. On your flash disk you should only the vtibackup See folder
  • Insert the USB stick into your receiver
  • Go to section MENU -> VTi -> Device Manager .
  • Select your USB drive and press the OK button.
  • Press the green button (Mount) – select /media/usb line mount point and click the OK button. And please leave Section Device Manager

  • Go to MENU -> VTi -> VTI Panel -> VTI Software Tools -> Expert Backup/Restore -> Choose backup location section and select /media/usb (Your mounter USB stick)
  • Go to section System settings restore and confirm that you want to restore the settings
  • NOTE: If in the “ System settings “restore” no backup exists , please select the section “ Advanced recovery ” and select the file “ vtibackup.tar.gz “!

  • Receiver will automatically restart. Now can Remove the USB stick from the receiver.
  • Go to step 3

3. Setting up the receiver after flashing

3.1 Tuner configuration

If after flashing and turning on the receiver the channel “ cable one “ didn’t work for you, you need to change the tuner settings. To do this, go to the section Main menu -> Setup -> Service search -> Tuner configuration and configure your tuner.

3.2 Obtaining the recipient's IP address

By default, the recipient should automatically obtain a network address (DHCP). To find out, you need to go to the section Main menu -> Information -> Go to About

In the Network section you will find your IP address (In my case it is 192.168.1.219)

If for some reason your receiver did not automatically receive an address, you will need to set up the network manually. This can be done in section Main menu -> Setup -> System -> Network -> Adapter settings

3.3 Set up Oscam

After restoring the backup for the first time, you need to restart Oscam manually.

Please go to section MENU -> VTi -> VTI Panel -> VTI Cam Center . Choose Oscam 1.20 rev: 11682 and press the YELLOW button (restart cam). Oscam will restart

You then need to add your access parameters to Oscam. To do this, open this Oscam web interface in a browser with the IP of your receiver. The Oscam web interface is on Port 8080 . In my case it is:

 http://192.168.1.219:8080/

You have to go to the section Files -> oscam.server go to , enter your connection details from the billing and click the button Save click.

Don't forget to click on that Save button to click!

4. Restart the receiver

Please restart the receiver completely after setup. Do not switch the receiver off via the socket, but restart it via the menu Main menu -> Standby / Restart -> Restart

5. Choose a playlist and watch it!

After restarting the receiver you can go to Sky Germany iCAM Bouquet go and enjoy the view.

6. Additional Information

Installed firmware has a root password for remote access via SSH/Telnet :

 Login: root 
Password: icam2022

We recommend that you change the root password and restrict or disable remote access when you don't need it.

7. Changing the ROOT password

To increase the security of your receiver, we strongly recommend that you change the root password.
To change the root password, log in to the receiver via SSH or Telnet using the login and password specified in Section 6. Enter the command:

 Password root

and set your new password